Gibbon Architectural Products

INSTALLATION CHECKLIST

KEY POINTS FOR INSTALLATION SUCCESS

Acclimatise

For 24 hrs on site before installation

  • Please remove plastic wrap beforehand
  • Do not install where substrate temp is under 10°C
  • Do not install where ambient humidity (RH) levels > 75%
  • Minimum 48 hours in controlled environment ahead of installation, for the duration of the
    installation and 48 hours post installation.

Allow enough time

Do not lay in wet.

Adhesive must achieve tack-off / tack-up.

Time will be dependent on temperature, humidity, airflow and substrate absorbency.

  • tretford T240 | SynSisal S340 –  Carpet ROLL
    • Place a small piece of carpet or finger into the adhesive.
    • When pulled away, strings or cobwebs should be apparent.
  • Modu-Tak PS – Carpet TILE
    • Allow adhesive film to become “translucent”.
    • Once translucent, the adhesive is in a dry tack mode and ready.

Upon Completion

Do not cover with impervious materials.

Temporary Protection:

Caution:— If impervious protective covering materials are applied over the newly installed product, condensation may collect and cause serious damage to the floor covering and/or bond strength of the floor covering to the substrate. (AS/NZS:2455.1:2019).  This will void manufacturer’s warranty.

Use Correct Adhesives & Underlays

tretford ROLL, RUGS (Adhered)

DIRECT STICK:

Adhesive: tretford 240
tretford to substrate – V2 (2.4mm) notched trowel (3m² p/ltre)

DUAL BOND:

Adhesive: tretford 240
Underlay to substrate- V1 (1.6mm) notched trowel (5m² p/ltre)
tretford to Underlay –  V2 (2.4mm) notched trowel (3m² p/ltre)

Underlays:
– Airstep BOUNCE 470 – 4.7mm
– Airstep BOUNCE 650 – 6.5mm (Domestic only)

SynSisal ROLL & RUGS

DIRECT STICK:

Adhesive: SynSisal S340
SynSisal to Substrate –  V2 (2.4mm) notched trowel (3m² p/ltre)

DUAL BOND:

Adhesive: SynSisal S340
Underlay to Substrate – V1 (1.6mm) notched trowel (5m² p/ltre)
SynSisal to Underlay –  V2 (2.4mm) notched trowel (3m² p/ltre)

Underlays:
– Airstep BOUNCE 470 – 4.7mm
– Airstep BOUNCE 650 – 6.5mm (Domestic only)

modulyss TILE

  • Adhesive: Modu-Tak – apply using V1 notched trowel

tretford TILE

  • Adhesive: Modu-Tak – apply using V1 notched trowel

INSTALLATION VIDEOS – tretford ROLL

INSTALLATION GUIDE & TECHNICAL INFO

Instruction Documents (PDF)

TDS button tretford ROLL 1
TDS button tretford RUGS Installed 1
TDS button tretford RUGS loose laid 1
TDS button tretford TILE 1
TDS button SynSisal ASTORIA
TDS button SynSisal LANGLEY
TDS button SynSisal MEDINA
TDS button SynSisal RAVENNA
TDS button SynSisal WINTHROP

Sub Floor Preparation

TDS button tretford ROLL sub floor
TDS button tretford RUGS subfloor
TDS button synsisal ROLL RUGS sub floor 1
TDS button tretford TILE sub floor

Technical Data Sheet

TDS button MODU TAK
TDS button synsisal S340 1
TDS button tretford T240 1
X